Kmc-controls TSP-5000 Series Instrukcja Użytkownika Pobierz pdf

TSP-5000 Series 1 Installation Guide

Installation Guide

Air Flow Transducer-Actuators

TSP-5000 Series

Mounting

Standard Instructions

The TSP-50xx transducer-actuators are designed to

mount on a standard 1/2" (13 mm) diameter shaft or

a 3/8" (9.5 mm) shaft using the optional HFO-0011

adaptor (see the HFO-0011 Adaptor Instructions

section below).

1. Set the TSP-50xx in the desired location.

2. Slide the TSP-50xx directly on to the 1/2"

diameter damper shaft. The shaft must extend a

minimum of 1-3/4" from the mounting surface.

3. Place the non-rotation bracket (supplied) on the

non-rotation tab.

4. Aachtheanti-rotationbrackettothemounting

surface using #8 or #10 self-tapping screws (not

included).

5. Depressthegeardisengagementbuonand:

a. Rotate the drive hub until the indicator stops

at the “90” mark if the damper is clockwise to

close.

b. Rotate the drive hub to the “0” mark if the

damper is counterclockwise to close.

6. Position the damper to full open.

7. Tighten the two 5/16"-18 hex set screws (see

diagram).

8. Depressthegeardisengagementbuonand

rotate the drive hub/damper to the closed

position.

9. Loosen the adjustable end stop, position it against

the damper position indicator, and retighten it.

HFO-0011 Adaptor Instructions

1. Mount the TSP-5003/23 actuator over the 3/8"

shaft.

2. Slide the HFO-0011 over the shaft into the drive

bushing of the actuator.

3. Align the adaptor slots with the set screws.

4. Tighten the set screws.

Mounting 1

Standard Instructions 1

HFO-0011 Adaptor Instructions 1

Connections and Wiring 2

All Models 2

TSP-5002/5022 Proportional Models 2

TSP-5003/5023 Tri-State Models 2

Setup 3

Calibration 3

Motor Operation Test 3

TSP-5003/5023 Tri-State Models 3

TSP-5002/5022 Proportional Models 3

Accessories 4

Maintenance 4

More Information 4

Important Notices 4

1 2 3 4

Podsumowanie treści

Strona 1 - Installation Guide

TSP-5000 Series 1 Installation GuideInstallation GuideAir Flow Transducer-ActuatorsTSP-5000 Series MountingStandard InstructionsThe TSP-50xx trans

Strona 2 - Connections and Wiring

TSP-5000 Series 2 Installation GuideConnections and WiringAll Models1. Remove the TSP-50xx’s wiring access door by pulling back on the door’s tab a

Strona 3 - Motor Operation Test

TSP-5000 Series 3 Installation GuideSetupThe TSP-50xx is factory calibrated to function with anSSS-1000seriesdierentialpressureowsensor.Usin

Strona 4 - More Information

Komentarze do niniejszej Instrukcji

Brak uwag

Kmc-controls TSP-5000 Series Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Czujniki Kmc-controls TSP-5000 Series. KMC Controls TSP-5000 Series User Manual Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Czujniki Kmc-controls TSP-5000 Series